SF310BEGQ5 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- wilma from Ashdown, AR
- Parts Used:
- W10918546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Pilot light wasn't working.
I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Dacula, GA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter was glowing but not enough to catch the catch the burner
Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from State College, PA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter Glows but gas never comes to ignite.
Since the broiler worked fine, I took the igniter from the broiler (exact same) and moved it to the bottom and sure enough oven ignited fine. I did this to isolate the problem, because it could have been either the igniter or the valve. I put the broiler igniter back on top when I got the new part, because it is used only 5% of the time. Be aware that you may need to rummage for some machine screws because the factory screws stripped when I removed them. The oven must have annealed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Schaumburg, IL
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven will not heat up
most difficult part was having to pull the stove out to access the Igniter wire connector. unplugged connector, removed 2 Igniter mounting screws, installed new Igniter and connected plug. very easy project. less than 30 minutes total thanks to website for perfect diagnosis of problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marva from McDonough, GA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light
I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Fredericksburg, VA
- Parts Used:
- 8184859
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The plastic trim piece broke and the bottom metal trim was rusted
The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!
Was this instruction helpful to you?
Thank you for voting!