RF3000XVW3 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burners wasn"t getting hot like they should
i just unpluged the old burner and slideed the new burners in place and they work great now like a new range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- denise from swartz creek, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element quit working
Removed the 2 screws that hold the element in place. Pulled the element forward about 3 inches and disconnected the two wires. Plugged the wire clips onto the new element and pushed the element back into place. Put the 2 screws back into place. This was a very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Aberdeen, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from burnthills, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bake element
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alene from INDIANAPOLIS, IN
- Parts Used:
- WP660532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners needed replacing
Pulled out the old burners and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Moore, SC
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating with bake element, broil element working OK.
Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from Fowler, CO
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the top of baked goods were not baking
turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Birmingham, AL
- Parts Used:
- WP660532
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
burned out stove eye, 6"
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIMMY from GRAY, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dead Short In Baking Element
Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from VALATIE, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven got warm - Temp light stayed lit.
Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNA from INDIANAPOLIS, IN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
underside of food baking stayed cold/frozen
removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!
Was this instruction helpful to you?
Thank you for voting!