RF196LXJQ0 Whirlpool Range - Instructions

Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.

removed drawer below oven, reached under stove and unplugged from outlet, pulled stove out from between cabinets, removed the 8 screws with 5/16 nutdriver from back panel and removed the panel, removed knob from switch , measured length of stem on old switch and compared it to the new switch ( my old switch stems was shorter than the new one so using a pair of pliers I shortened stem per instructions that came with new switch, this was very easy to do ), removed the two screws holding switch to stove and removed the old switch, then I transfered one wire at a time from the old switch to the new one until I had all the wires connected to the new one, used same two screws holding old switch to the stove to mount the new switch to the stove and put knob from old switch onto the new one, installed back panel to stove using the same 8 screws, pushed stove back into place between the cabinets and plugged the stove into the outlet, put drawer back in place below oven door, reset clock and tried out the new switch, so far so good only time well tell if I fixed my problem because it only happens once in awhile

I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Parts arrived extremely quickly. Easy assembly. Would highly recommend partselect.com. Thank you.

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

My husband had no problem at all with the replacement of the exterior glass.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.

I simply put the control knobs on the shaft and
they worked great. I love them. Thank you.

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.