RF364PSBQ0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Philip from Coral Springs, FL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Element went bad
I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.
Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.
Part was on order and I still received it within three days.
You guys are the best, I recommend the site to all of my friends and family.
Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.
Part was on order and I still received it within three days.
You guys are the best, I recommend the site to all of my friends and family.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Troy, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
i had a dish explode in oven wanted to remove lower element to clean and didnt unplug it first unscrewed it pulled element out and shorted ot out. so remember to alway cut ppwer before working on anything .lesson learned.!
Easy unplug appliance take racks out unscrew two screws gently pull out element unplug two wires put new one in reverse .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alicia D from Indianapolis, IN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
My bottom element was no longer heating.
First I checked to make sure the power was off with an electrical meter (wiggins). Next I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then pulled off the 2 wires replaced the element and put the 2 wires on the new element. I screwed it back into place and tested the element. When I turned the oven on my new element began to glow red and the repair was now complete. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Olathe, KS
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out - Easy repair
Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNA from INDIANAPOLIS, IN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
underside of food baking stayed cold/frozen
removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Jamestown, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element not working
Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Ansonia, CT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom bake element cracked
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from St. Michael, MN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heat element burnt out
First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.
Was this instruction helpful to you?
Thank you for voting!
Bake element blew
remove all element that is held with two screws and install the new one. easy fix! and a lot cheaper than a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erica from Merced, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom burner in oven not working
Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Snellville, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element sparked & smoked, then wouldn't work.
Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Abingdon, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The baking element had burned out
First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Levittown, NY
- Parts Used:
- WP3169203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The glass had broken
My son ordered the part, which came very fast,
It was a perfect fit, and the job went very smooth. I have no story to tell except that Mom was happy to have the oven again and a VERY helpful son!!!!
It was a perfect fit, and the job went very smooth. I have no story to tell except that Mom was happy to have the oven again and a VERY helpful son!!!!
Was this instruction helpful to you?
Thank you for voting!