YGW395LEGB6 Whirlpool Range - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.

I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

Replaced the grates. Very pleased. Great service, correct parts, happy customer.

I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!

Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a bundle on service call fees.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

I researched the problem on the internet, and all of the data led me to believe I had a bad igniter. My husband and I viewed a youtube video about installing a new one, and then I read step by step instructions on another site. We thought we would be able to easily do this ourselves, so we ordered the part from PartSelect, and I received the part within a couple of days. After taking the back off the stove, and the pan off the bottom of the oven, we attached a string and pulled through the old wires, and then attached the new wires on the igniter and pulled them to the back of the stove and connected them. The part was exactly what we needed, and now the stove works like it did when it was brand new! I was very happy with the results! MEF

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

I read it may be the temp sensor. Ordered a new one. Took a minute to undo three screws holding the back on, and one screw for the sensor. But still didn't work. Then realized maybe the oven was changed to Celsius. In manual - open door, hold broil for seconds and changed back to Fahrenheit.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Purchased 2 piece broiler pan from this site

Removed the door just like you would do when cleaning the oven; I placed the door on a blanket on the kitchen table and carefully disassembled the door. There were more parts than I expected so keeping track of where everything went was important. I might add that without the use of my cordless variable speed drill motor removal of some of the screws would have been difficult. Adding the weight of the drill motor with sufficient push power I was able to tap the switch which "snapped" the screw loose. Don't think I could have done it with a hand type screw driver without stripping the head. Knowing your tools is very important.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation