GY396LXPS02 Whirlpool Range - Instructions

Followed suggestions from prior Customers that had same problem.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.

Tools required - #2 Phillips and needle nose pliers. (possibly a new spade connector and stripper/crimper) (possibly a multi-meter)

Shut off the power and slide the range forward about 8-10 inches from the wall. It does not need to be completely in the open and perhaps would not need to be moved at all. Some of the parts may be stuck with accumulation of cooking debris and grease, depending on age. Disassembly will be a bit more difficult than a new range because of this. Clean everything up before reassembly.

Open the oven door. Remove two screws, one on either side, below the control panel. Lift and work the control panel loose. It has two bullet shaped posts that engage slots in the front of the range. These are tight. Be patient and work it by lifting and pulling and wiggling the entire control panel. When loose, it will lay down flat supported by all of the wiring harnesses. In our case it did not stress the wires. If concerned, support it somehow.

There is a galvanized bracket that runs most of the width of the range and retains a rubber gasket on the front edge of the glass. Remove two screws that hold this bracket. The bracket easily comes loose, set it aside.

There is a stainless steel trim piece on each side of the cooktop, running from front to back. Each one is held in place by one screw in the front. Remove the screws and the two trim pieces will slide forward and can be removed. Set them aside.

There is a rubber gasket across the front edge of the glass cook surface. Remove it. The cooktop glass can now be lifted and worked loose from the rear rubber gasket that seals across the back edge. Set the cooking surface aside in a safe place. You now have access to the burner elements.

Using the needle nose pliers, work the spade terminal connectors loose from the burner that is to be replaced. Note their positions. The burner is held in place by two spring clips that attach the burner to a galvanized support bar that runs from front to back of the range. A screwdriver can be used to compress each clip allowing a tab to be lifted out of a slot in the galvanized bar. If needed, you can remove one front screw that holds the bar in place and lift it for better access, but while this is not necessary, it allows for a better view of the retainer clips and the tabs that fit into slots in the support bar. With both clips released, the burner is free to be removed.

Our burner clearly had a break in the coil, so there was no doubt about the cause of non-functionality.

The spring clips must be removed and transferred to the new burner. With both burners, face down on a bench, remove the screws that retain the clips to the old burner. Make note of the index numbers at the position of the old clips and place them at the same position on the new burner. This positions the burner when it is mounted so that the terminals are properly positioned to allow the wiring harness to be attached as it was.

With the spring clips in place on the new burner, place the burner back in the range and engage the tabs in the slots on the support bar. They will snap back into place. Reconnect the spade connectors. The burner should now be tested before reassembly. (see later)

In our case, when power was reestablished (but burner control in the off position) the Surface Hot light was on art all times, so we knew something was wired wrong, even though it was re-connected exactly as it had previously been. There are slight differences between the new burners and old burners that apparently impact the wiring. There are no markings on either the old burner or new burner to give clues as to how it should be wired. Neither was there any advice in the instruction sheet that came with the new burner. We tested all of the terminals with the power on (burner off) to determine what voltages were where and removed the cover of the small box to which the terminals are attached. This box contains small switches, and we were able to determine the new wiring scheme. By wiring it exactly as it originally was, we had inadvertently put power to the Surface Hot light full time and the same potential to both sides of the coil so it would not heat. With this corrected, it worked fine.

As always, reassembly is just the reveres of the steps taken to disassemble. It is a bit tricky to place the glass back in the rear gasket. Just be careful and work it into place. Also the front control panel can be challenging. Line up the bullets with the slots and work it into place. It will snap into place when it is close with the aid of the heel of your hand.

One other note. One of the four wires in the harness had a smaller female spade connector which had to be cut off and a new one crimped on in order to fit the new burner.

Because of the wiring logic issue that had to be troubleshot, this took about three hours, which included disassembly and reassembly twice (because we reassembled before testing), figurin

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.

Removed locking device

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Removed the top light, removed the 2 screws in the light pan and pulled the control panel over the stove top. Held controls exactly as mounted, removed wires from the old control and pushed on to the new ones. Removed the 2 screws that held the controls to the panel, tossed the old control and put in screws to the new controls securing them to the panel. Remember to unplug the range first. And, a secure bar that maintains the push button panel will have to be maintained, so tape before removing any parts.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

EASY. FOLLOWED THE YOUTUBE INSTRUCTIONS ON THE WEBSITE.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!