SF272LXTD1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gordon from Yukon, OK
- Parts Used:
- WP8273103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Control Knob Broken
Remove old knob and put new knob in. About 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mauldin, SC
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear drawer slide was broken.
Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfield Bay, AR
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not get self cleaning oven to engage
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Saint James, NY
- Parts Used:
- WPW10107820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Henry from Manitou Beach, MI
- Parts Used:
- WPW10108260
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F1 error code caused by bad control panel
Instructions for error codes were listed in a booklet hanging on the back of the range. Have unplugged and replugged the unit twice before after getting the F1 code after a power failure. This time the error code remained, indicating a damaged control box. Referenced the model number to the Part Select parts list, ordered the part on a weekend and it arrived on Tuesday. 4 screws to remove the back cover. 4 screws to remove the old control box. 3 plugs to disconnect. 4 screws to install new part. 3 plugs for the wiring. 4 screws to install back cover. Plug in the stove and slide back into position...about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Marlton, NJ
- Parts Used:
- WPW10268483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner grate burnt out
Replaced grates
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Scotch Plains, NJ
- Parts Used:
- WP8273103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob on range was broken
Just put it on, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Arlington, VA
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven has not heat
Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Anthem, AZ
- Parts Used:
- WP8273103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing control knbs on stove.
This could not have been any easier. The site walked me through selecting the correct part and it arrived quickly. When I got the part, it slid right on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from camarillo, CA
- Parts Used:
- WP8273103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
Just push knob into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from New York, NY
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake would not work all the time
The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Lexington, KY
- Parts Used:
- WP8273103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gas range control knob was cracked
pull off the cracked knob and pushed on the new control knob.??
Was this instruction helpful to you?
Thank you for voting!