RF366BXVN0 Whirlpool Range - Instructions

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

Screwed in light bulb and glass protector

I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!

Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!

Turn off the oven's breaker. Remove oven grates. Unscrew two screws holding in the bake element. Slowly pull the bake element out a few inches. Using pliers, CAREFULLY unattach the connectors from the ends of the bake element. DO NOT FORCE OR CRUSH THE CONNECTORS. Using your hands only, attach the connectors to the ends of the new bake element. Re-insert the element into the back of the oven. Re-insert the screws to attach the new element to the back of the oven. Turn the breaker back on. Turn the oven on bake to test the element. Go have a beer to congratulate yourself on saving $75 or more. Should take about 10 minutes if you're proceeding slowly & carefully. It'll take 2 minutes if you're reckless and get lucky, but it'll take 2+ hours if you're reckless and all goes wrong, causing you screw up the connectors and need to go buy some plus crimpers, etc.

I got online, and "Googled" bake element and Whirlpool (model #), and selected PartSelect by chance. The website had a diagram of my oven with parts and it was easy to select the right part. I paid extra to have it shipped overnight and it arrived the next day. I removed two screws, disconnected the old element, and replaced it with the new element. It worked!! I think I saved a lot of money by doing the repair myself. (I am a 66 yearl old woman and will choose PartSelect by choice for future appliance repairs.)

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I took out 2 screws and installed new element! It took 5 mins.

very easy

Backed out two screws, disconnected two wires from faulty element, connected wires to new element, screwed back into place. (New element was ordered by phone and received the next day.)

Used screwdriver to unfasten the old element from the oven frame. Then unplugged the two wire plugs from the back of the old element. Reversed the process to install the new. Couldn't have been any simpler.