RE960PXVW1 Whirlpool Range - Instructions

First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

I followed the instructions provided.

Opened package and stuck it on. Easy - Peasy

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

came only I had to order the set again

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

The replacement of the glass was easy, I removed the door and placed on work bench. As long as you lay the parts out in an orderly manner the reassembly goes pretty good. The longest time was cleaning the glass's that were dirty from the inner broken glass.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.