RF315PXYN1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from TAYLORS, SC
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface element out
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from DELTONA, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
8" FRONT BURNER STAYED ON HIGH HEAT/WOULD NOT REDUCE TEMPERTURE
REMOVE BACK OF RANGE, REMOVE BURNER KNOB. REMOVE SWITCH CONTROL REMOVE WIRES. REPLACE WIRES ON NEW SWITCH. INSERTED ALL WIRES REPLACE NEW SWITCH RE REPLACE ALL SCREWS. CHECK SWITCH. TURN BRAKER BACK ON. CHECK SWITCH FUNCTION. ALL IS FINE. PUT BACK ON RANGE SCREW IT IN PLACE. MOVE RANGE BACK IN IT POSITION.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WHITE RIV JCT, VT
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element temperature inconsistent
Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from OLIVE BRANCH, MS
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top broiler element busted
Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from Mackay, ID
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
N/A
I followed the instructions provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from YORK HAVEN, PA
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front burner would only stay on high
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Robert from Downers Grove, IL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element arced bigtime so we figured it was time - 18 years old!
I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Aberdeen, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn on the oven to heat up for cooking, Heard a ark sound, open the oven door and there was a fire on the element. Turn off the oven.
I had to pull the stove out from the wall and discounted the power source from the wall. Than I used the a phillips screwdriver take out the heat element. There was now problem fixing the stove. Lowell Moxley
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from burnthills, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bake element
unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from South Burlington, VT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up
Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from las vegas, NV
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element burnt out
removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda
Brenda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEPHEN from SEMORA, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom element of the oven stopped working, therefore, we could not bake anything.
First, I turned the breaker off to the oven, that's the most important step.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.
Next, I turned on the oven to make sure the oven was not energized.
I then took out two phillips screws that were holding the baking element in place.
Next I pulled the element out slowly to expose the wires that connected to the element.
I removed the connecters, took out the damaged element, replaced it with the new element.
Last, I screwed the two phillips screws back in, and saved a $65.00 service call.
Was this instruction helpful to you?
Thank you for voting!