RF3020XVF0 Whirlpool Range - Instructions

Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!

Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.

lifted up burner and pulled it free from its connection, then removed drip pan. used my cordless drill to drill out broken stabilizer clip. cleaned up chips from the drill process before installing new clip. installed clip with enclosed screw and nut. I then installed the new burner by lining it up with the connection under the cook top pushed it place and lowered it into the stabilizer clip. Then I turned the burner on to try it out, but I waited for about one hour before turning on the burner because it was cold from being outside.

First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.

Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.

Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Someone did the repair for me.

I removed the block, cut and spliced the wires to the new block and installed the burner. I used the new style block kit and saved about $30. It worked great!

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.