SF362BEGN0 Whirlpool Range - Instructions

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

I broke the old trim when cleaning. New trim kit went together great. No screws needed because of new design. Best tip I can give is that the side trim pieces around the oven door go behind the glass on the door not in front of the glass. Visual instructions would be great.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

Remember how you remove the glass. The side brackets go under the glass.

Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!

Excellent delivery.

Used new differant screws to mount it and cut and spliced the wires to use the org. Plug.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.

Lifted burner top remover 6 screws lifted plate removed switch and installed new switch, took about 20 mins to complete job

Since the broiler worked fine, I took the igniter from the broiler (exact same) and moved it to the bottom and sure enough oven ignited fine. I did this to isolate the problem, because it could have been either the igniter or the valve. I put the broiler igniter back on top when I got the new part, because it is used only 5% of the time. Be aware that you may need to rummage for some machine screws because the factory screws stripped when I removed them. The oven must have annealed them.

The igniter would glow but no gas was released to the burner. I was told that the igniter is bad because it is not getting hot enough to open the safety valve to release the gas to the burner. I turn the gas off and unplugged the oven. Opened the oven removed the racks then removed the two screws that hold the bottom plate of the oven. Now I can see the burner and the igniter. The igniter is held on to the burner with two screws. Unscrew then and unplugged the wires. Then replaced with new igniter. Replaced everything that I removed. Plugged oven back in and turned on gas. Then started oven, it takes 45 sec. for the igniter to get hot enough to release the gas and everything was working.

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!