SF114PXSQ0 Whirlpool Range - Instructions

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

The same part was selling for almost $30 each so I was glad to find in on Parts Select. It only took a few minutes to put on and my oven is back to working condition. Thank you Parts Select

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

it was abit difficult to remove the rusted hinge because of rust, but after getting it out and securing the new one, I realize I had an even bigger problem. The new hinge was closed and the spring was very tight.After a closer look at the other side of the oven door where the hinge was intact, I saw a hole in the hinge when it was opened. So I opened the new hinge by pulling it open and exposing the hole, put a pin in the hole.I then put the hinge in position and put in the screws.But now the door wouldn't go into position. I then had to put pins on both hinges and slide them in at the same time,locking them into place.This was the first time i ever took out an oven door or attempted any stove repair.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

It only took my husbend 6min to put in the new oven igniter. But it did not work, so I call your center and the rep there talk my husbend and told him how to unluck the key bord, and that worked. Thank you for all the help.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!

Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!

ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!