SF195LEHQ6 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Marion, KS
- Parts Used:
- WP3196262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
oven light flashing off and on when door closed
removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Reynoldsburg, OH
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken trim
remove the hinge stays they just clip in
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
remove the door. took out screw at bottom of door.
replaced trim.
replacing the door was a problem i didn't have pins to put in the spring loaded hinges so i used nails to hold hinge in position.
so make sure to open oven door first insert pins or nails in hinges then remove door. It would have took 10 min. to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlaine from Romeoville, IL
- Parts Used:
- WP8273104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the part that fits on the stem to turn the knob had broken. I tried to tape it together, but that did not work.
since it was the control knob, all I had to do was to push it right onto the stem, and it was finished. Using the web site to find the correct item was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Galloway, NJ
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
scratches and paint detoriation on bottom part of oven
Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.
Was this instruction helpful to you?
Thank you for voting!
broken bottom drawer glide and missing rivet on drawer front panel
Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.
The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.
The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WOODSTOCK, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven wouldn't heat above 300 deg. F.
I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Saint Michael, MN
- Parts Used:
- WP3195546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom drawer
It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wagner from Miami, FL
- Parts Used:
- WPW10293048
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
I just intalled the part, but the problem continued
I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Sinks Grove, WV
- Parts Used:
- WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom heavily corroded; difficult to clean.
Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hardwick, VT
- Parts Used:
- WPW10293048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable), Wrench set
The Gas Safety Valve would not shut off. Gas conyinued to flow when oven switch was turned off.
Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Maysville, GA
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear stove drawer glide
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Carteret, NJ
- Parts Used:
- WP8273104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
center hold of kn ob cracked
Took knob off ordered new one put it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rustin from LARAMIE, WY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
FAULT CODE F-3
REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3
Was this instruction helpful to you?
Thank you for voting!