RS610PXEW0 Whirlpool Range - Instructions

Remove burners using my hands and replace new burners using my hands.

The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Replaced the lower heating element with a new part.

I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

Removed door per manual instructions, then disassembled door components until I could remove the hinges. Nothing wrong with either one visually but, hoping the springs had become weak over time, I ordered replacements from PartSelect, knnowing I had a 30-day return window if my diagnosis was wromg.

It was right. Door now closes just fine.

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was able to fix my stove without a repairman. Saved $$$

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

I removed surface burner and drip pan from stove. Then drilled out the remaining part of the old stabilizer clip. Once clip was removed I installed the new stabilizer clip with the screw and nut that came with the clip. Then I placed the drip pan back into position and installed the burner and locked it into the new clip.

I had to remove the original clips (broken or damaged). This was the hardest part -- the clips were held on by rivets (not screws), so I had to pound/punch them out (using care so not to damage the stove top). Once I punched the rivet out all that remained was a small hole, I just used the small nut and bolt that came with my stablizer clip kit and mounted the new clips. Everything worked out fine.

Replaced with the new burner works like new. Thanks a bunch!

Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.