RFE3000W1 Whirlpool Range - Instructions

Someone did the repair for me.

Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.

First I checked to make sure the power was off with an electrical meter (wiggins). Next I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then pulled off the 2 wires replaced the element and put the 2 wires on the new element. I screwed it back into place and tested the element. When I turned the oven on my new element began to glow red and the repair was now complete. Super easy.

First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

I took the old wires and plug off and replaced it with the new block it works fine

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done

EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .