RF316PXYN4 Whirlpool Range - Instructions

simply removed screws & old part.., replcd new part & screwed back into place.

turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.

I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.

removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.

Replaced broken element with new one, part was delivering quickly and work great

This repair couldn't be easier. I turned off power to the range, removed the oven racks, unscrewed the two screws holding the element, carefully slid the connectors off of the terminals, reconnected them to the new baking element, put the screws back in. Entire repair took less than 10 min. Not much harder than changing a light bulb. Works like a brand new oven.

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.