SF315PEKT0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Bixby, OK
- Parts Used:
- 98010184
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clip on bottom of glass door broken
At the top of the oven door, lossen the door handle. The handle also holds the top of the glass. One side at a time. Pull the bottom of the glass out far enough to see where the clip mounts. Insert clip. Wiggle the glass into it. Do the same on the other side. You may have to take the screw all the way out so be sure and hold on to the glass securely. Retighten top screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverside, CA
- Parts Used:
- 98010184
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lower trim broke
The same part was selling for almost $30 each so I was glad to find in on Parts Select. It only took a few minutes to put on and my oven is back to working condition. Thank you Parts Select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Leander, TX
- Parts Used:
- WP98005317
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Handle broke on Range Door
Handle was not able to install easily; tried to hammer rivet to secure new handle to door & broke glass panel...now have to buy a new stove because this one has been discontinued.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Woodstock, GA
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Gas oven would not heat up
Moved oven away from wall, Turned off gas and unplugged electrical from wall. The igniter has a coupler plug that you have to unplug from behind the unit. Take out the bottom drawer. Remove the 2 nuts holding the igniter in place. Remove old igniter. Replace with the new igniter, screw in nuts and thread connector wire to back of unit. Reconnect the igniter behind the unit. Turn on gas and plug in electricity. I checked to make sure it worked before pushing it back into place. I also took time to clean up while the oven was pulled out so it took about an hour - 15 minutes to replace the part - 45 to clean up. Works and looks just like a new oven range!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Princeton, IL
- Parts Used:
- W10918546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Mouting Holes Did Not Line Up, Wires Had A Differant Plug Than Org.
Used new differant screws to mount it and cut and spliced the wires to use the org. Plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prisciliano Jr. from El Paso, TX
- Parts Used:
- WP98005317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven door handle broken
Removed broken pieces,installed replacement handle on glass and push nuts,then installed on to oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chatsworth, CA
- Parts Used:
- WP98005317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
took off the old handle. put on the new one in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from Stryker, OH
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven igniter
ordered the part and in less then 24 hours from ordering the part it was shipped and delivered and my husband and I put the part in took us no time at all very easy to do... 2 years ago i had this same problem and called a guy in the area cost me $200. I had dinner in the oven by 5 that night!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dominic from Tucson, AZ
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old igniter glowed red but was too cold
Shut off gas and unplugged electrical cord. Removed grates; oven floor and flame spreader and then unbolted old igniter with nut driver. Removed shield in rear of over with Phillips screwdriver and unplugged igniter from power socket. Removed old igniter and replaced with new. Bolted new igniter into place with nut driver and plug into rear socket. Turned on gas and plugged in electric to test igniter; saw white glow and flame on in a minute. Replaced rear shield, flame spreader, oven floor and grates. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Broadalbin, NY
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The oven wouldn't light.
Our oven wouldn't light as the ignitor wasn't getting hot enough. I ordered the part from your company and got it in just a few days. A quarter inch wrench and one plug, done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from South New Berlin, NY
- Parts Used:
- 98005982
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
going from lp gas to nat. gas
Repair was easy-----getting the parts was the hard part. Ordered 4ea only got 1, ordered again and only got 1, spoke to rep again and they promissed to fix the problem. Next time i got 8 ea. IN the end they refunded my money and all is well. Many people involed in getting this part but the company did its job and fixed the problem. (just give it time)
Was this instruction helpful to you?
Thank you for voting!