GY395LXGB3 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven Light bulb and gasket needed replaced
Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Plainview, NY
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheel broke off oven drawer
I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Wildomar, CA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven temp not hot enough
Followed Mfgs instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Wildwood, MO
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had broken causing the oven not to heat up.
removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Buford, GA
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light lens broke when self clean cycle was used
I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Castroville, TX
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Oven Element for Whirlpool Oven
Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Hutchinson, KS
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven not heating up.
Remove two screws. Plug n play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Jacksonville, FL
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element broke in one part.
TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Oly, WA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would bake for several minutes then turn its self off. It would not come back on until you reset it. The time varied from 10 to 15 minutes before turning off.
I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from McHenry, IL
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Temperature Sensor Replacement
The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Sandusky, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from San Jose, NM
- Parts Used:
- WP3184533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket for oven light wore out and needed replacing.
I very simply replaced the gasket where it belonged and I was good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Blanket, TX
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element inoperative
Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!