RF214LXTQ0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Parts Came With No Instructions And We Couldn't Find Directions On Line.
We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Grantsville, UT
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
terminal block back of range shorted and burned
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Roberts, MT
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wiring Block shorted due to moisture and Stove had no Power
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from kissimmee, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top element was burnt out small burn hole in element
removed the screws that were on back side of oven securing panel that covered element terminals disconnected wiring to upper element then went in side oven area removing 4 upper mount screws that were holding upper element in place then removed old element and reinstalled new in same order was removed..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Channelview, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
R&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Brazoria, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Fairport, NY
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from San Antonio, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .
Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Las Cruces, NM
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven shutting off after temp reached 350
Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy Scott from Tupelo, MS
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The heating element had burned through from food spillage and sticking
I removed the broken heating element while waiting for the new part to arrive and cleaned the oven. SO much easier without anything in the way. Once the part arrived and it was wonderfully packaged...Easy to open but very well protected, it was a snap to connect the 2 power wires and then screw in the 2 screws to secure the heating element. I was back to baking in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eloy from Andrews, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element not working
Turn power off at breaker box, remove back cover inserted wires into element, done and ready to be use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph R. from Candia, NH
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not heating properly.
Removed rear panel and removed switch. I placed wires from old switch to the new one. re installed switch an back panel.
Was this instruction helpful to you?
Thank you for voting!