RS677PXYQ0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harry from Kannapolis, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bake element burned out
removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Ardmore, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element burned out
Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from North Kingstown, RI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element burned out
The repair was easy. I turned off the power to the oven at he curcuit breaker. Using a phillips screwdriver, I removed the 2 screws that held on the old heating element. One screw came off easily. The other screw required a little WD-40 and alot of force, but I was able to get it off. I then removed the 2 wires from the terminals on the old element. Again, it required a little force and wiggling of the contact.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from Oconomowoc, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Oven Bake Element Didn't Work
Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Harrison Township, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was cracked in half
Pulled old one out, installed new one with a twist of the screw driver. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Lodi, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating up
I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, VA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element broke into pieces.
1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard G. & Linda L. from Reading, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Well my wife's oven heating element burned out
Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from NESHANIC STATION, NJ
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
split element
simple replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from maple plain, MN
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The lower element was not heating up
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBBIE from BARTLETT, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element not getting hot enough
Unplug oven unit from outlet or flip the breaker to disconnect the electricity. Used screwdriver to remove face cover, pulled wire connections from posts of old bake element. Attached wire connections to posts of the new bake element(they just slip on the posts). Aligned the face cover flush with the oven wall and replaced screws to hold cover on. Reconnect electricity and ready to bake. It is very simple.... We were very pleased with how quickly the element was delivered after ordering it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Wethersfield, CT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The lower element was not heating up
I just removed two screws and disconnected the push on clips I then cleaned the botton of the oven and replaced the element. And it works just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Marysville, OH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element broke
removed racks and door (could have left door on but made it easier to reach screws) removed 2 screws from old element unplugged the 2 wires and reversed process for new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Chillicothe, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element in oven burnt out
I took out 2 screws and installed new element! It took 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pawling, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element burn out.
The repair was simple. Two screws and it popped in. The part arrived quicker then expected. Done in no time.
Was this instruction helpful to you?
Thank you for voting!