GY396LXGT4 Whirlpool Range - Instructions

First , I turned off the circuit breaker to the oven.
Next, I removed the two screws at the front of the range top and slid the top out until I could disconnect the multi-plug connecting the wiring harness to the stove.
I then took the entire top out to a table and set it upside down. It was easy to unbolt and disconnect the lead to the element. One of the leads was burnt, so I had to replace it. I slid the new element into place, bolted it down in the same orientation as the old one and reconnected the leads.

I slid the entire top back into place on the range and re-installed the securing screws. Then I flipped on the circuit breaker and turned the element on.
Success! Perhaps I didn't really need to change the element since the burnt lead was the cause of failure. But its good to have a new part installed anyway.

I ran numerous tests to eliminate the on/off switch and to ensure the wires were not defective. Thus I came to the conclusion it must be the burner was defective. I ordered the part from parts.com. I received the part in less time than what was advertised. The part arrived in good condition. I placed the part in and it worked just like new.

Thank You

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

The repair went very well the most difficult was getting the door off. There is a certain way to do it as the springs in the door are very strong. It went well except for a small cut a thumb. The repair is easier with two people at least to get the door removed. You must be very careful to remember how the door comes apart. Be careful to not touch the glass putting it in once it is installed it is impossible to get the finger prints off. With help of a friend or in this case my son along with a couple of bloody marys it went well and we had fun.

thanks

Easy.
Remove 2 screws.
Remove wires from old element.
Attach wires to new element.
Replace screws.
Took 5 minutes.

With glass side down:
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)

Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.

took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

Just as others said. Remove top holdown bolts with nut driver. Prop range top up.
Use a pair of plyers to remove wires (make sure you have a diagram to restore).
Use screwdriver to remove element hold down spring and wire holder. Replace element and replace wires and screws.

Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564