GS395LEGQ7 Whirlpool Range - Instructions

Removed two screws and the front of the door popped off. Replaced the bottom metal piece that the glass front slides into. It was a piece of cake.

I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.

Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.

Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.

Replaced bottom trim included in kit.
Installed side door trim.
While trying to slide glass front in place both plastic side trims broke.
Had to use already broken door trim and glued in. Just hope when use oven glue doesn’t melt and will have to replace entire oven.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

Took knob off ordered new one put it in place

exchanged old with new

This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.

The parts I got were exactly like the original knobs and were a breeze to snap on. Range working great again . The wife is happy again lol

1. Removed old knobs and the adapter piece with pliers ( I tried using cheap universal knobs from Lowe’s first that were garbage)

2. Push the new knobs onto the shaft and voila. Perfect fit and range looks new again. Replaced all 4 on my black whirlpool gas range

Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.

Replaced the knob

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!