Models > RF010EXRW1 > Instructions

RF010EXRW1 Whirlpool Range - Instructions

Jump to:

All Instructions for the RF010EXRW1

Customer:: Gerald from Rochester, NY
Parts Used:: W10196406RW, W10196405RW
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

old bowls could not be cleaned. These new bowls make the stove look great

Removed old bowls and replaced with the new bowls. Also, thanks for your help with the rang knobs. You did not have the replacement knobs for my range but you gave me help in where I might get them. With the new bowls and knobs the range looks like new. Thanks again for all your help.

Was this instruction helpful to you?

Customer:: Gail M from Lockport, NY
Parts Used:: 330031
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner was slow heating at times. Moved back burner to front still same thing.

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

Was this instruction helpful to you?

Customer:: Robert from Brookfield, CT
Parts Used:: WP660533
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner failure

Removed and replaced burner unit.

Was this instruction helpful to you?

Customer:: judy from coarsegold, CA
Parts Used:: WP660533
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

burner fell apart

Just plugged it in and away I went.

Was this instruction helpful to you?

Customer:: PATRICIA*NAYLOR from NEW PRT RCHY, FL
Parts Used:: W10196406RW, W10196405RW
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Generic Drip Bowls Made The Burners Tilt.

Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.

Was this instruction helpful to you?

Customer:: Leslie from Spring HIll, FL
Parts Used:: W10196405RW
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

The burner didn't work because it had the wrong drip bowl

Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.

Was this instruction helpful to you?

Customer:: Barbara from Pacific Palisades, CA
Parts Used:: WP660532
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner no longer connected with electric power source

I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.

Was this instruction helpful to you?

Customer:: Judith from Staunton, IL
Parts Used:: 330031
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner keep coming on and going off had a short in burner plug-in block.

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Was this instruction helpful to you?

Customer:: Ann from Memphis, TN
Parts Used:: W10196406RW, W10196405RW
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Drip Bowl beyond cleaning

Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!

Was this instruction helpful to you?

Customer:: Earl from Union Mills, NC
Parts Used:: 330031
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

burner would not heat up the connection was bad

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

Was this instruction helpful to you?

Customer:: Margaret from New Hope, PA
Parts Used:: WP660533
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Burner stopped working. Replaced burner & block.

We read comments by other DIYers and then looked at the video on YouTube. Our range is old and the screw holding the clamp for the block was too tight to remove so we removed the block from the old clamp and left clamp intact. Turned the circuit breaker off. Cut the existing wires and wired the new block to them. Put the block back into the old clamp, put new surface burner in and good as new. My boyfriend and I did it together but I could have done it myself - it was that simple. Thanks PartSelect for quick delivery and excellent DIY info.

Was this instruction helpful to you?

Customer:: vincent from Martinsville, VA
Parts Used:: 330031
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

electric surface unit not working

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

Was this instruction helpful to you?

Customer:: Charles from Villa Ridge, MO
Parts Used:: 330031
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

one burner that would not heat and others that would not out out much heat

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

Was this instruction helpful to you?

Customer:: Christina from West Des Moines, IA
Parts Used:: WP8203546
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

range installer broke a screw off & busted the plastic piece

Had to screw off old terminal block & screw on new one

Was this instruction helpful to you?

Customer:: Bonnie from Price, UT
Parts Used:: 330031
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

stove burner no longer would heat up burner element

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

Was this instruction helpful to you?

All Instructions for the RF010EXRW1