RF010EXRW1 Whirlpool Range - Instructions

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

I ordered the 2 burners that were not working. When I got the burners, I discovered that one of the burners was still working and the wiring under that on had burned out. So I ordered the little box kit and repaired it. I only needed to strip wires and twist together and replace the small box. Now all are working and I am cooking with all four burners again. All for about $50.

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

Since it was a plug-in burner, only needed to pull it out and put the other one in.

Another thing I would like to say is that I was very well pleased with the service from partselect.com. I was unable to find the burners in my area.
Was very helpful in selecting the part and was very efficient in sending it.

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.

Clipped and rewired plug in socket and put new burner in

Simply removed new burner from box and plugged it in! Very pleased with 3 day speedy delivery. Confident my 32 year old cooktop will continue to give many more years of service with any parts needed from PartSelect.

pulled out old burner and pushed in new burner.
No tools needed.

After finding the correct Y-frame, inches and watts in a surface burner, it was easy to just slide in the slots. Tested, and it was perfect. Now it makes all of the other burners look bad. Thanks. Your site was the only one, that I was sure I had the correct part.

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!