RF314BBDQ0 Whirlpool Range - Instructions

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I took out 2 screws and installed new element! It took 5 mins.

Funny, I suppose. We decided to buy a new stove given the old age of the old one. Problem is, on delivery day it wasn't delivered and we discovered that there wasn't even one in the warehouse. At that point we got ticked and decided to look into the problem. The website led us right to the problem. We ordered, the part arrived the next day and the replacement was simple. Just unscrew the holder inside the over, unplug the old element and plug in the new. I needed needle nose pliers because one of the wires slipped behind the insulation. We also bought a thermometer and found that the calabration was right on the money. Happy campers... we saved $400.

Found breaker box and shut off power to stove, Check to make sure you turned the right breaker off before you attempt to put you hands in it, also make sure all the switches on the stove are in the off position . Open Oven Door, I used a Phillip screw driver to remove the two screws holding the Bake element in place . pull out to reach wire connections and gently pull connectors from element. Remove the old Bake element and Install the New one,by reversing process in removing the old one. after you have it back in place turn breaker back on at breaker box turn oven control to Bake setting, turn Oven Temperature control to around 200 degrees and Element should began to glow bright orange, job complete, it's that easy!~

My handyman removed the old burnt our element by removing two screws and disconnected two wires and reconnected wire and screwed the unit into the oven wall. This repair was a breeze! Thanks for making my life easier!

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

The repair was easy. I turned off the power to the oven at he curcuit breaker. Using a phillips screwdriver, I removed the 2 screws that held on the old heating element. One screw came off easily. The other screw required a little WD-40 and alot of force, but I was able to get it off. I then removed the 2 wires from the terminals on the old element. Again, it required a little force and wiggling of the contact.

Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!

simple replacement

With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Simply remove two phillips screws, unplug and replug. Thanks to the quality parts I bought here it saved me $65.00 on the part alone. Locally $85.00 plus shipping.
Thanks guys for your help.

Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.