RF3020XGN0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Mariposa, CA
- Parts Used:
- WP3188987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Switch
Made sure was off, Removed rear panel, removed 2 screws, removed wire clips from old switch, installed wires on new switch, installed switch with 2 screws, re-installed back panel, reconnected power and checked switch function. OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT E. from GLENDALE, CA
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Replace aged Drip bowls
Lift and remove heat elements
Lift and remove Drip bowls
Replace Drip bowls and heat elements
Lift and remove Drip bowls
Replace Drip bowls and heat elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean-Claude from Miami, FL
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element was taking time to warm up
Wire connection was damaged, replaced end piece
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Midwest City, OK
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The heating coil was no longer working.
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from BROAD BROOK, CT
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Generic drip bowls in the stores did not fit
Very easy remove the burner and instill the drip bowls
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Black Mountain, NC
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from harrisburg, NC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element went out on the stove
My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Rockingham, NC
- Parts Used:
- WP3196231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
removed the old and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Normand from Lincoln, RI
- Parts Used:
- W10856603
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broiler element not working
It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Maysville, GA
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear stove drawer glide
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from Logan, OH
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven was blowing a circuit.
Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.
Was this instruction helpful to you?
Thank you for voting!
Burned out wires and 2 switches.
Unscrewed the switches and let the switch hang while replacing one wire at a time. Followed instructions on wire replacement. Exact parts, only shaft on 6" switch was too long -- okay, because it is designed to break off a piece on end of shaft, then the knob fit. Everything was perfect.
Was this instruction helpful to you?
Thank you for voting!
Infinite switch bad and receptacle heat damaged
Removed back plate, replaced infinite switch.
Replaced receptacle holder. Took a moment to see how to install wires into the receptacle, no instructions on orientation of wires into the receptacle. Wired receptacle per instructions. Placed receptacle into holder and installed burner. Burner Burner would not lay flat, receptacle longer than original. Removed receptacle from holder, plugged in burner and placed burner into position.
Replaced receptacle holder. Took a moment to see how to install wires into the receptacle, no instructions on orientation of wires into the receptacle. Wired receptacle per instructions. Placed receptacle into holder and installed burner. Burner Burner would not lay flat, receptacle longer than original. Removed receptacle from holder, plugged in burner and placed burner into position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph K from PAHRUMP, NV
- Parts Used:
- WP3196548
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The oven light shorted out causing the safety thermostat to blow.
Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light
Works great again...without the light
Was this instruction helpful to you?
Thank you for voting!
Broken drawer glides
Simply removed the bottom drawer, unscrew the old broken glide, and attach the new glide. Simple and no hassles.
Was this instruction helpful to you?
Thank you for voting!