GR475LXKS0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GREENBRIER, TN
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from mesa, AZ
- Parts Used:
- W11230488
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
chemical etching of black painted finish on drawer front panel
took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FOUNTAIN INN, SC
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia Josephine from N RICHLND HLS, TX
- Parts Used:
- W10823692
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace old Element
The new element wiring placements were totally different from the old element. Lucky for me the lettering printed on the terminals for each pole was the same as on the old one. It was just a matter of matching up each terminal pole lettering. The instructions that came with the new element were of no help at all. Youtube was my best helper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaime from Deltona, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Elements burned wouldn't heat
First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from JACKSON, WY
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element non operational
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from RADCLIFF, KY
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dual Surface Element went out
Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WHITE RIV JCT, VT
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element temperature inconsistent
Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from LYNNWOOD, WA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element died
Followed instructions on urine that you provided. Instructions were great.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TRACY, CA
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Over heating element.
Just turn off power , remover screws. Remove and plug in new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from BRYAN, TX
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Back left burner went out
I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!