GS440LELT0 Whirlpool Range - Instructions

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.

Took off outer trim. Put new glass in and returned trim. Very easy, looks great.

removed old and installed new

Remove oven racks. Remove bottom of oven. Mine was held in place by two large screws in the back part of the oven. They did not screw into anything. Lift out bottom from the rear. Remove burner cover plate by lifting the front and pulling out. Mine was not screwed in. The igniter is mounted on the burner and held by two 5/16 small bolts. The top one is easily accessible. The bottom is a real witch. You need 1/4inch socket set with universal connector to remove. There is a single wire attached to igniter by a wire clip. The wire is accessible by removing the bottom pan storage drawer under the oven door. Unclip the old attach the new. Screw two small bolts back in and replace things you took out. TURN GAS AND ELECTRICITY OFF BEFORE YOU BEGIN. Parts select should allow the igniter to be sold separately rather than connected to the burner. I only replaced the igniter. Replacing the burner would be a real chore.

First remove the oven racks and the burner cover in the bottom of the oven. There are two phillips screws near the back. Loosen the screws but it is not necessary to completely remove them. Pull out the bottom cover and this will expose the burner. There is one phillips screw at the front of the oven and one at the back. Remove these screws and set aside. You should be able to remove the burner and unplug the wire connected to it. Replace with a new burner in the reverse order. Plug in the wire and make sure the new burner is seated properly over the gas valve. It lines up pretty easily. Put the rear screw back in but be careful not to drop it into the hole otherwise you will have to use a magnet to retrieve it or pull the oven out because it will be on the floor. Replace the front screw and put everything else back together. Pretty easy job

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!

Remove old grate and replace with new one.

Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.

I broke the old trim when cleaning. New trim kit went together great. No screws needed because of new design. Best tip I can give is that the side trim pieces around the oven door go behind the glass on the door not in front of the glass. Visual instructions would be great.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

Remember how you remove the glass. The side brackets go under the glass.

Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Excellent delivery.

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.