SF377PEGW0 Whirlpool Range - Instructions

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

To replace, the front glass slides into two holders on the bottom and three groves in the handle, then two screws to attach handle in place on the door.

this is the easiest repair possible. take out bottom drawer.. disconnect power cord. igniter is above burner grid.remove the two screws {be careful not to lose them}. move stove out from wall. from behind stove remove three small screws holding tin cover. and unplug the connector..install new igniter from under stove and plug in connector. install tin cover and move stove back in. replace bottom drawer. and plug in power. replacement saved the repair cost or replacement of a new stove..

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

I slid the range out about 8 inches from the wall, and having unplugged the range and looked at the diagram from the Parts Select site, I used a mirror and screwdriver to remove the screws holding the small rear cover. From there I removed the one screw holding the spark module and that way I was able to hold the old and new one side by side to move the wires. Reversed the process, easy peasy.

used a screwdriver. took very little time and effort

Easy. Slide oven away from wall. Turn gas off and unplug. Open oven door. Remove grates and lift out bottom tray to access igniter. Igniter is affixed to burner tube using (QTY=2) 1/4” bolts. Used socket wrench due to limited space for nut driver handle length. Detach igniter. Got to back of oven and remove the protective plate at the bottom. There are three phillips screws. Verify you have the correct cable for igniter by tugging on igniter in oven. Pull old igniter out. Replace old igniter with new using old bolts! Run igniter cable through back using same hole as old igniter. Plug in connector in the same fashion as prior. Before reassembly, test oven. Plug oven in and turn gas back on. Set oven to bake and set temperature. If igniter lights the gas burner tube, you’re done! Reverse process to put oven back together. Job takes 20 minutes, maximum. Saved a bundle!

The repair went well. Only took a few minutes. Oven is 21 years old and still working. I figured why throw away if still working. Thank you Select Parts for coming to my rescue. Will keep you in mind.

1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!