GERC4110SB2 Whirlpool Range - Instructions

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

just replaced the broken glides with the new ones.

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from the range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Remove top oven door,remove two hex head screws located underneath cook top at the front on both sides,slid the range top forward approx. three(3) inches to obtain access needed to unplug the wiring harness, located behind the vertical part of the cook top,removed the cook top,placing it on a padded table with the glass side down,disconnected the three (3)wire spades and unscrewed three screws anchoring heating element to the cook top frame, replaced defective heating assembly with new. Repeated above steps noted above,in reverse order. And yes, all work was done after power was shut off at power panels dedicated oven circuit.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.