SF114PXSQ1 Whirlpool Range - Instructions

Screwed in light bulb and glass protector

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

The same part was selling for almost $30 each so I was glad to find in on Parts Select. It only took a few minutes to put on and my oven is back to working condition. Thank you Parts Select

First of all my wife is a clean freak. She lifted range top one to many times and broke the front burner tubes. She went to lite front burner after cleaning and got a very big bang because of the gas leak. Found brokentubes and called parts select with model info and got some great help getting my parts. Took only ten minutes to replace tubes after parts came in. Thanks for the help. Also the parts cost less at parts select than my repair store in my home town

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

I pulled the stove out from the wall & took the back lower right cover off. Unplugged the power cord & disconnected the igniter from the power. Took shelves & bottom cover (took two screws out)from oven. Used nutdriver to remove old igniter, then pulled the connector through into the oven, discard. Put new igniter in place with nutdriver.Push connecting cord through to back of stove.Replace bottom cover & shelves. Plug cords together & plug cord back in to outlet.Turn stove on & igniter works!!! Push stove back into place & bake a cake! :)

Opened lower door of stove located ignitor removed 2 small screws that secure part, took guard off back of stove unplugged wire connector removed part plugged new ignitor in re-installed guard, re-installed 2 screws that secure ignitor. Turned stove on oven lit problem solved. This is the 3rd time i have used instant repairman on parts select to fix 3 different applicances and have saved hundreds of dollars fixing it myself with the help of parts select.

I shut off the gas and removed the back plate and disconnected the wires. Then I unscrewed two screws from the igniter and replaced the old with the new. Then I snapped the wires together and put the back plate back on. The oven works great!

I removed the oven racks, removed the oven floor and the oven burner cover, pulled the range out and removed the small panel on the back which covers the igniter connector. I disconnected the old igniter, removed the two screws holding the igniter in place and removed the old igniter from the oven. Then screwed on the new igniter, fed the wire through to the back and connected the new igniter. Turned on the oven and voila' we have ingnition! The oven is working again but I'm getting the "F2" routine sometimes. It doesn't do it every time but when it does I unplug and replug and then it works. I'm a 67 year old female and I considered it very easy so pretty much anyone should be able to do this repair.

Removed a cover plate on the back of the stove. Unplugged the old igniter. Pulled the bottom drawer out. Reached in under the stove and undid the 2 screws holding the igniter in place. Screwed the new igniter in and put everything back together. The only tricky bit was reaching the igniter through the bottom drawer opening.

I disconnected gas line and removed screws holding the 4 pilot assembles, lifted the top of stove and removed and replaced the tubing. Pretty straight forward installation..