RF376PXDW0 Whirlpool Range - Instructions

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I'll tell you.......PartSelect said the items would take from 3-5 days.....I got them in 48 hrs. I turned the breaker to the oven off. I unscrewd two screws from the back of the oven and pulled the element out and took it off of two connectors. Repeated the same with the broiler element. Job done saved $200.00...Job was quoted at $259.00

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

First, I removed the oven door by pulling it open to where it loocked and then I pulled it up and off the hinges. Second, I removed the two screws on the top of the door and three screws on the bottom ot the door which allowed me to remove the front of the door. Third, using a nut driver, I removed the frame holding the inner glass to the door and removed that. Fourth, I removed the frame holding the broken glass to the door by removing the screws using my nut driver. I carefully removed the broken glass and vacuumed the channel that had the gasket in it. The gasket was fine so I did not have to replace it and will return it. I placed the glass in the frame on the gasket and reassembled the door in reverse order of how I had disassembled. All went smooth as silk.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
reverse to install.
It was great to find a place that has the parts you need, and supper fast delivery service.

Thank you Ed Andrews
sound, lighting, and video systems engineer.

removed the screws that held the element in place. Pulled out the element out about three inches and disconnected the two wires, put the new one in, did the reverse and done. the best part was I orderd it on line after 3:oopm on a thursday and the part was delivered by saturday morning- wow!

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.

Removed 2 screws on heating element mount plate. Pulled out heating element 3 inches and used needle nose pliers to remove the 2 connector clips. Reconnected connector clips by hand to new heating element. Put heating plate back into original position and reinstalled 2 mount screws.

Very easy, thanks for the great support