RF364BXBQ0 Whirlpool Range - Instructions

1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!

Turned off the breaker to the stove. Removed the two screws holding the element in place. Pulled off the wire terminals, removed old element. Reconnected the two wires, slid new element into place, reinserted the two holding screws, turned back on breaker. 5 minutes.

Pulled old one out, installed new one with a twist of the screw driver. Easy!!!

I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.

It was so easy. I removed the baking racks. Then I unscrewed two Philips head screws that held the rack in place. Then I pulled the two connections apart from the wiring. Plugged the new element into the wiring. It was as simple as sliding it in and out, replaced the screws, and within minutes I was back to baking again.

unplugged oven unscrewed old element replaced with new one plugged in oven it only took 2 days to get new element saved time and gas

I order the part on 7/29 and much to my surprise, it arrived the very next day. It took less than 15 minutes to remove the old element and installed the new one. It was a little difficult to unplug the old one and took quite a bit of pulling but it came out okay. Plugging in the new one and screwing on the cover plate was easy.

removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

Very easy, thanks for the great support

With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
reverse to install.
It was great to find a place that has the parts you need, and supper fast delivery service.

Thank you Ed Andrews
sound, lighting, and video systems engineer.