RS610PXYH4 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vickie from Richmond, VA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element not heating
The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard G. & Linda L. from Reading, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Well my wife's oven heating element burned out
Well it was quite simple to replace all I used was a long Phillips screw driver,the job only took me 10 minutes to complete,thank you so much for the part you sent me it was the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Kannapolis, NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bake element burned out
removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Chillicothe, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element in oven burnt out
I took out 2 screws and installed new element! It took 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from ZEPHYRHILLS, FL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element burned out
Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Charlotte, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element quit heating
un plugged oven from wall Unscrewed 2 screws pulled out old heating element and plugged in new heating element then plugged stove back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrill from Houston, TX
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hole in Cooktop Burner
Simply removed new burner from box and plugged it in! Very pleased with 3 day speedy delivery. Confident my 32 year old cooktop will continue to give many more years of service with any parts needed from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, VA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element broke into pieces.
1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Black Mtn., NC
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element caught fire and burned into
turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Ardmore, PA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element burned out
Removed the two sheet metal screws holding the element, Unplugged the contacts and plugged and fastened the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from North Kingstown, RI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element burned out
The repair was easy. I turned off the power to the oven at he curcuit breaker. Using a phillips screwdriver, I removed the 2 screws that held on the old heating element. One screw came off easily. The other screw required a little WD-40 and alot of force, but I was able to get it off. I then removed the 2 wires from the terminals on the old element. Again, it required a little force and wiggling of the contact.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Reversing the process, I slid the contacts onto the terminals of the new heating element. Then, I screwed the backplate of the new heating element in place at the back of the oven with the 2 screws I had previously removed. I then restored power at the circuit breaker. The whole job took less then 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Harrison Township, MI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was cracked in half
Pulled old one out, installed new one with a twist of the screw driver. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Lodi, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating up
I removed the two screws for the bake element, diconnected the two wires attached to the bake element. I then reattached the wires to the new bake element, secured it with the two screws and I was done. It took five minutes and the oven works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from Oconomowoc, WI
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Oven Bake Element Didn't Work
Unscrewed two screws, pulled the element out of the socket, pushed in replacement element, screwed in the two screws--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alain from Federal Way, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom heating element not heating
Grabbed my courage with both hands, then with my other hand I used a screwdriver. Delicately removed 2 screws holding the broken element. Once that delicate operation was done, I took out the old and place the new. Once again grabbed the screwdriver and with agility replaced 2 screws. Then, I turned on the oven and Voila, ready to bake some enchiladas.
Winner, winner, chicken dinner.
Winner, winner, chicken dinner.
Was this instruction helpful to you?
Thank you for voting!