1745^0A Whirlpool Range - Instructions

First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running.
Fuses or breakers are verified ok and on.
Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cable from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches.
Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt.
Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below.
After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot.
Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

Replaced lid switch, but problem still continued.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3

Called my son. He took off the back put the belt on and we were ready to go.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

New knob arrived promptly and matched exactly.

just slipped them on

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

All I had to was fit the knob on the stem of the burner and push on it and turn the knob.

My stove is well over 15 years. When I bought my house over 7 years ago the stove was ancient and had only 2 knobs. Well, one of the two fell apart and I could not afford to replace the stove. Lo and behold there was a part number on the back of the knob and I did a goggle search and found an identical replacement. The kind they sell at the store, the adjustable ones, did not work. Anyway, I placed the order during the New Year holiday and I got my knobs in 2 days. Beautiful and shiny and best of all I can use all my burners for the first time ever.Thank you

Needed new knobs to go on the stove. I only had one left in the original ones for the stove that was bought 27 years ago.