SF325PEGN1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leonard from Hamilton, NJ
- Parts Used:
- 4342528
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Lower igniter wouldn't light oven didn't heat up
Ordered the part from you it came the next day didn't need to pay for upgraded shipping, nice. Followed the easy instructions on your site. It had all the right hardware it literally clipped on the wires and bingo worked like a champion. I've done this on many ovens it sure beats calling an appliance repairman and getting ripped off for a 15 minute job. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Demorest, GA
- Parts Used:
- WP8053360
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner head was warped.
I used a screwdriver to take two screws out and then pulled up on the burner head. I then installed the new part. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CONSTANCE from LAWTON, OK
- Parts Used:
- WPW10202217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven handle
I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ashland, WI
- Parts Used:
- WPW10202217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Scews from old one didn't fit the new one.
I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.
Was this instruction helpful to you?
Thank you for voting!
The old panel becamed worped & the finish was distressed.
Took the old one out and replaced it with the new one, fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Brookline, MA
- Parts Used:
- WPW10256908, WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When I originally purchased my stove, there was a large paper describing stove features. It was glued on and when I removed it, it left glue which I could not remove. I s hould have returned stove, but I didn't.
So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph W from Anaheim, CA
- Parts Used:
- WPW10447925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Grate coating was damaged
Remove old grate and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Oakton, VA
- Parts Used:
- WP8053456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced a stove burner grate
No tools necessary. Shipment was extremely quick; I was very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rusty from Franklin, TN
- Parts Used:
- W11032529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not light
remove burner - 2 phillips head screws. Raise top - cut wire to ignitor. Strip wires and connect with a wire nut. Drop in new ignitor - reinstall burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boise, ID
- Parts Used:
- 4342528
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not ignite
Removed the bottom drawer, oven racks, and the oven floor panel. With a #2 cross tip screw driver, I removed the old igniter, replaced it with the new one and tested the unit. When the new igniter began to glow I turned the unit off and reassembled the oven - JOB DONE less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from WESTERVILLE, OH
- Parts Used:
- 8184859
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dented front trim
Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Oceanside, CA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Damaged Socket When Removing Bulb Base
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oconomowoc, WI
- Parts Used:
- W11032529
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cracked igniter no longer functional
The first challenge is always how to get the appliance apart; in this case how to open the top of the stove. There are two clips one on each side towards the front that you need to push in to release the top. However before you do this you need to unscrew and remove each of the burners from the top of the stove. After that, push the clips in with a flat blade screwdriver from each side to lift up the top. You will need to remove completely the top back plate on the rear of the appliance to get to the igniter module where you plug in the wires from the individual igniters. Then you also need to remove the top four screws from the lower rear plate to allow it to be pulled open enough to help thread the wire from the new igniter through. After that you simply figure out which wire (they are individually colored based on their position on the burner) and disconnect from the igniter module. Carefully pull it out watching where it came from so you can rout the new wire in a similar manner. Then remove it completely pulling it through the top of the stove and replace with the new igniter. Reverse the steps to put everything back together and you should be good to go. Be prepared to take a little extra time to clean the cook top as once you remove the burner you will see everything that has over the years accumulated between the burner and the stove top. All together it took me about a 1/2 hour (including the cleaning).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Safety Harbor, FL
- Parts Used:
- 8184859
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
rust
Excellent delivery.
Was this instruction helpful to you?
Thank you for voting!