SF325LEKW0 Whirlpool Range - Instructions

cut 3/8" off each handle supports and used no. 10 1/2' sheet metal screws to secure handle and door front to the oven door. The supports had to be shorten to allow the door front to fit correctly on the oven door.

Turn gas off at tank. Oven rack out. 2 screws out of flame spreader and remove. 2screws from ignitor. Pull oven out from location to access rear bottom cover. 2 screws out and unplug ignitor. Guess what ? Reverse order. Not worth paying gas company over 250 dollars.

I just removed the bottom panel in oven and the igniter was right where the flames should be and I removed the two screws and replaced with new part. I replaced bottom oven panel. You need to remove rear panel and plug wire and replace rear panel. My problem was solve. It took 20-30 minutes tops.

I took apart the bottom of the oven to see the ignighter. I moved the oven away from the wall and took off the metal plate that covers the ignighter electrical connection.Unplug the old part and plug in the new one. With the nutdriver remove the two screws holding the part onto the gas tube. Save the screws and attach the new part with them. Turn on the oven to see if the gas tube lights. If all is good put the metal plate on the back of the oven and replace the other oven parts. Make biscuits!!

Simply put the new ones on. I was very happy with how quickly the grates were shipped!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.

If your version of the stove has the square blank manifold tube, this superseded part does NOT work! The instructions that came from Whirlpool are so small and unreadable. I had to scan / take photos of them so I could blow them up to make them readable.
If you follow the instructions to the letter, the part will NOT work in the stove. I had to make several extra modifications and further "grinding" along with moving the screw holes to get the part in; and it still does not fit 100% but it is working.
I called Whirlpool for help / addition information and that was a waste of time, they sent me in circles and gave me no answers.

This part may work great in other models, but it does not fit SF310PEKW0 with the square black manifold tube.

For reference, I actually know what I am doing when it comes to things.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

Even though the old igniter still glowed, I took Part Select's advise that it may be getting weak and ordered a new one. They shipped the part out the same day, very nice, however FedEx decided for some reason to hold it for five days before moving it along. Boo! When the part got here the fix was straight forward, just a matter of unscrewing a small back panel, unplugging the part, taking the old igniter off the burner and reversing the process with the new part. Oven lit right up. Thank youfor your advise and quick service.

Unplug range from electric service.
Turn off gas supply to range.OVEN
Removed the floor panel of the oven housing.
Unscrew,and removed the heat deflector. (Caution sharp metals)
Used 3/8 socket set to unscrew the old Igniter, used same bolts to mount new Igniter.
Go to the back of the range removed the metal guard held by four Phillip screws, unplug old harness, plug new factory plug (do not alter harness)

Pull range out from the wall. Unplugged the old igniter. Took the broiler assembly out of the bottom of the oven by removing 6 philips head screws. Removed the 2 screws holding the igniter & removed. Screwed the new igniter in place , replaced broiler assembly. Got back behind range plugged in the new igniter slid range back into position & turned the oven & it works like a new one.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes