WFC315S0JW4 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Saint James, NY
- Parts Used:
- WPW10107820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfield Bay, AR
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not get self cleaning oven to engage
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Clinton, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner goes full hot at any setting
First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Adamsville, TN
- Parts Used:
- WP8523166
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Side trim broke
take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Seminole, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The large burner sometimes stayed on high too long, burning food
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Cameron, MO
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
could not control temp on burner
Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Noah from Richardson, TX
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
corroded, rusted drip bowls
replace
Was this instruction helpful to you?
Thank you for voting!