YWFE550S0LV3 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Salem, OR
- Parts Used:
- WPW10434452
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dual element control switches were no longer regulating the burners properly (either on or off, no in-between)
1. Pull the stove away from the wall and unplug the stove from the 240 volt receptacle.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Greensboro, NC
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Duarte, CA
- Parts Used:
- W10355051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from BRIDGEBORO, GA
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
Range door would not close correctly. Spring loaded latch was bent.
Look up Whirlpool parts and was able to order parts thru PartSelect.
Item were deliver with in three day. I was able to watch the video provided my PartSelect on how to replace the spring loaded latch. The job was easy and I was able to install the range door. Thank you PartSelect.
I would recommend Whirlpool PartSelect for parts and service.
Ernest Martinez,
ernestmartinez918@gmail.com
Item were deliver with in three day. I was able to watch the video provided my PartSelect on how to replace the spring loaded latch. The job was easy and I was able to install the range door. Thank you PartSelect.
I would recommend Whirlpool PartSelect for parts and service.
Ernest Martinez,
ernestmartinez918@gmail.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from GAHANNA, OH
- Parts Used:
- WP9755770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Heats up very slow
Unplugged the range, remove back electrical cover and component cover. Unscrewed old temp sensor and replaced it with new. Oven heats quicker (just by indication) since the probe is only a sensor..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!