MER6755AAB Whirlpool Range - Instructions

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

After the repair I determined that the door did not need to be removed from the stove. The top 3 screws needed to be taken out, the front clase needed to be slid out by pushing it right to left or left to right. Then the bracket that held the inside screw assembly needed to be removed. The new handle needed to be installed and the bracets put back into place. The front glass needed to be reinstalled right to left or left to right. The hardest part of my install was putting door back on the range, the hinges kept popping out of place before setting into the range. The best way to replace the hangle would be to not remove the door from the range.

1) Unplugged the electrical cord and removed the oven door (only when easy); and, jockeyed the oven into better working area.
2) Removed about 9 screws holding rear sheetmetal backing plate to disconnect each of 2 electrical wires from the old element.
3) Removed 2 screws holding element to back of oven and 2 screws from small bracket supporting end of element to top of oven.
4) Replacement element was severely damaged. It was at the very bottom of a box 20 by 15 by 15.5 inches high with the large continuous bubble wrap stacked only on top. Each of the wire ends were sharply bent; one almost 180 deg. pointing in the opposite direction, and the other about 120 deg. The element itself was about 4-5 inches out of square. Using two large needlenose pliers I carefully bent each wire back to its proper place. Next I carefully exerted pressure on the element to gradually form it back to as near its correct shape as possible. (Only the inside of the shipping box showed the signs of possible damage.)
5) Installation- The element, from inside the oven, was placed back through the two holes in the rear of the oven and secured with 2 screws.
6) The bracket supporting the front of the element was slid onto the element and attached to the top of the oven.
7) Attached the 2 electrical oven wires to the 2 element wires, making sure there was good clearance to prevent any short circuit, plugged the oven cord in to 230volts, and checked it out with power to the broiler to give myself some confidence that the damaged wires would not quickly break. It seemed to work and I unplugged the oven.
8) Reinstalled the backing plate with the original screws, plugged oven back in, and moved the oven back to its place and replaced its door. It is working and my wife is cooking.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

after removing the element as decribed, my husband replaced the new element with the screws removed and it worked like new, less than 10 minutes and we appreciated so much the element was received so quickly.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

I've been trying to remove the bracket at the roof of upper oven so I can get to the broiler element itself. The screws are in place so tight, the won't move. I've used regular as well as ratchet screwdrivers and the screws still won't move. I don't want to spray WD 40 in oven because of a possible fire hazard, so I haven't changed out element yet. Tried calling customer service for advise, but to no avail. All other screws loosen easily. What should I do next.