MER6755AAB Whirlpool Range - Instructions

When the element failed, it continued to glow nearly white-hot and slowly burned along a spiral path on the element. I figured this MUST be due to a voltage leak - the control was OFF on the range.

I shut off the breaker, removed the two screws where the element goes through the back of the oven, pulled the element forward and pulled the wires off of the element. (Found it handy to twist the wire connectors outward to prevent the wires from slipping through the back of the oven.)

A new element won't "fit" exactly but you can easily push it into position to get the screw holes to line up. Total time was less than 15 minutes.

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

1. Open oven door to first detent, then pull it up off the hinges.
2. Pull oven out from counter 10-12 inches.
3. Hinges are accessible from the outside of the oven.
4. Remove 2 screws on each hinge and remove old hinges.
5. Put new hinges in place and try to insert mounting screws.
6. Wonder why screws won't start in threads.
7. Examine new hinges and notice they are not threaded for the screws.
8. Screws are not self-tapping, so go to basement and get tap & die set.
9. Use 10-24 tap to make threads in new hinges.
10. Put new hinges in place and insert mounting screws. Tighten.
11. Pull hinges to first detent and put oven door on hinges.
12. Push oven back into place in counter.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

Power turned off. Door of the oven lifted off. Four screws removed, old element pulled out to reveal electrical connectors. Wires easily removed, and element discarded. New element connected to the two conductors, four screws installed and the job was completed.
Very easy. Took about 10 minutes.

The best I can say is to remove door. take screws out from the bottom and sides first. Clean all layers of glass before installing handle.

Pull out the range...hardest part.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.

We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.

once I figured out how to remove door it was a piece of cake for a 72 year old man.

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Took out 2 screws along the underside of the glass top. Unhooked the glass top from the back of the range lifted it up and supported it with a board. Removed 2 screws holding the old burner in place and lowered it down onto the insulation on top of the oven. Removed the wires and reattached them in order to the new burner. Removed the screws holding the brackets to the old burner and attached them in the same places on the new burner. Reattached the burner to the bottom of the glass top the placed the glass top back in its proper position and put the 2 screws back in holding it in place. Plugged in the range and tested the burner to make sure it worked. Then slid the range back into position. All done in about 30 mins. Not very difficult at all.

This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.

Replacement part was exact and worked perfect.

Turn off the circuit breaker for the range.

Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.

Pull the bottom of the front panel out about 30 degrees and lift off the top.

Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.