JDR8895AAS Whirlpool Range - Instructions

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.