WFG505M0BS4 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frederick from Quincy, FL
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
didn't heat up as it should and pots would not sit level
just pull out moving fromm side to side until unplug from outlet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Annapolis, NC
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
none
no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Baton Rouge, LA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire on one of the burners was frayed and exposed
took old burner out and put in new burner. No problem. Easy greasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JohnPaul from Ft. Bragg, CA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element burned out-burners did not work
the new element came, I unplugged the old one and plugged the new one in. 5mins max
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Avon, IN
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn Oven Seal
If you have some mechanical ability it is a eazy fix, remove the 2 screws attaching door to oven, disassemble the back screws, and inner panel, remove oven seal, and reverse the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenia from Miramar, FL
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace grill elements with convention coil elements
Easy as 1-2-3. Opened the box, took out the new electric coil elements, plugged it in to our stove and it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from East Otis, MA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
elements would not heat up
Disengaged the old cartridge and replaced with the new one ---simple as pie-----the real issue is that it was ordered and delivered with-in 4 days---in a well pack and insulated box---great service---
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Pauline, SC
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners would not heat properly, and eyes could not be leveled.
Pulled old element out, cleaned electrical connector. Cleaned drip pan. Replaced with new unit. The new element was of a better design than the original. I will order second set soon to match.
Wife very pleased too.
Wife very pleased too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Walnut Grove, CA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old element cracked
Simply pulled old element and plugged in the new one. The pattern of 3 flat spades and a round on the end of the element matched so it was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Jonesboro, LA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wanted to replace the grill unit
removed the grill element and plugged in the new cartridge element. very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elissa from Fort Thomas, KY
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new coil element for my 20+ years old stovetop.
Plug in...done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W.C. from Elberta, AL
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Large element on one cartridge & small element on the other cartridge
First of all, I could not believe how quickly I received the 2 new Jenn-Air Coil element cartridges!! It seemed like I had just ordered them and next thing I knew, Fed-Ex was ringing my doorbell to deliver them!! Also, I received both cartridge boxes at the same time so this was really great! My experience in the past in ordering two of one item is that the second item is usually shipped a few days later.
This was one of the easiest installations & repairs I have ever done! Given the age of the stove, the old cartridges had a burner on each one that did not work properly. Also, one of the cartridges was beginning to rust on the underside, due to age.
It took approximately 2 minutes to remove the old burner cartridges and install the new ones. All I had to do is slightly lift the lip edge of the cartridge and "unplug" it from the stove which merely entailed either moving the cartridge toward me or away from me, depending on which side of the stove I was replacing the cartridge on. Then, I just simply slid the cartridge into the appropriate plug in the stove. That was it!
I immediately checked all burners and I could not believe the difference! The burners immediately reached the desired temperature whereas the old elements that worked took a couple of minutes to heat properly. Now, the Jenn-Air looks like a new stove and is ready for holiday cooking!!! Thank you so very much for processing my order quickly. I will definitely order any future parts needed from your company. On a scale of 1 to 10, I give you an 11.
This was one of the easiest installations & repairs I have ever done! Given the age of the stove, the old cartridges had a burner on each one that did not work properly. Also, one of the cartridges was beginning to rust on the underside, due to age.
It took approximately 2 minutes to remove the old burner cartridges and install the new ones. All I had to do is slightly lift the lip edge of the cartridge and "unplug" it from the stove which merely entailed either moving the cartridge toward me or away from me, depending on which side of the stove I was replacing the cartridge on. Then, I just simply slid the cartridge into the appropriate plug in the stove. That was it!
I immediately checked all burners and I could not believe the difference! The burners immediately reached the desired temperature whereas the old elements that worked took a couple of minutes to heat properly. Now, the Jenn-Air looks like a new stove and is ready for holiday cooking!!! Thank you so very much for processing my order quickly. I will definitely order any future parts needed from your company. On a scale of 1 to 10, I give you an 11.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from missoula, MT
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner going out
plugged new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from SOUTH LAKE TAHOE, CA
- Parts Used:
- JEA7000ADSA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No problem, just wanted 4 burners instead of 2 + grill
This was a plug-in cartridge, so it really didn't need to be installed. However, as I unpacked it, I noticed that there was a blue plastic film sticking out from the edge of the underside. We had to take the cartridge apart to remove the plastic film. I didn't want to take the chance of it catching on fire.
Was this instruction helpful to you?
Thank you for voting!