MER6755AAS Whirlpool Range - Instructions

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

Remove two screws on front of range top. they are exposed when you open the oven door. lift and pull back top. unplug two molex connectors, need to squeeze the plastic sides. remove top range to floor. remove six screws and take glass top off metal frame. element is held in with some simple clips and three push on connectors must be removed. replace with new element and assemble in reverse order.

FIgured it was either a bad heating element or a realy expensive repair so I purchased a replacement element to rule out the simple and inexpensive possibility. Pulled oven out from wall and disconnected power supply. Removed retaining bracket from top of oven, two screws that held in heating element, disconnected from fittings, replaced with new element, and reattached screws and retaining bracket. Plugged in power supply, tested lower oven (it worked just fine) pushed oven back against the wall. Threw away the old element and packaging. Job done.

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Removed the 5 screws holding the stainless steel cover on the oven door, removed handle. Attached new handle and reattached cover.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

I pulled the range away from the wall to gain access to the back.I turned off the power to the range at the circuit breaker panel. I unscrewed all little screws on top of back plate then removed it carefully.I took several pictures on the connections to the ECR board.I watched a video on You Tube which was helpful.The difficulty was getting the connectors off without breaking them. By carefully putting the edge of the flat blade screwdriver under each connector and twisting it gently I was able to get this little plastic locking pin to let go.Once this pin unlocked I was able to remove the connector from the prongs on the range. After removing the ECR board I carefully removed the decal from the front of the old board by pushing the edge of a sharp putty knife slowly under the decal. Following the pictures I took I was able to connect the new ECR board connectors properly and re-assemble the board into the top of the range after attaching the decal being careful to line it up properly.Once the range was back against the wall I turned on the power and set the clock then proceeded to test the small top oven which now worked fine.I found the people at at this stie to be very knowledgeable about what parts are needed to fix common problems.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

I removed the two small screws, gently pulled the element outward, slid the wire connectors off the ends of the element legs and reversed the process to install the new one. THE ELEMENT STILL DOES NOT HEAT. There must be a bad switch or thermostat at the ON switch area. That will be checked out by a Repair man as soon as I can get a schedule from him.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

First, I would like to appreciate providing a diagram of the product with a clear schematic. It was very easy to identify the item that I was looking for(an element). The serial number shown against the schematic enabled me to identify the item and pace the order.

Second, the item was delivered on time as promised.

Finally, the item that I purchased was very easy to replace. It came in as a full assembly. Just removed 4 screws, removed the damaged element and plugged in the new one. Thats it!!!

l certainly recommend this site to others to perform a self repair of their home appliances.