GW395LEGB3 Whirlpool Range - Instructions

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.

The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.

Replaced both rollers....Quick and Easy!!

The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!

Followed Mfgs instructions.

No tools necessary. Shipment was extremely quick; I was very pleased.

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

Replaced valve, 3 pipe connections 4 wire connections, still did not work, small flip up valve was set at off position, set to on, still did not work, replaced ignitor, bingo that was the real problem, reinstalled old valve, still working fine; returned new valve assembly for full refund! Thank You

Pulled insulation out of the way to feed wires through. Might have helped to tie pull string to old wires but fishing them through was not to difficult.No need to cut wires; it is not a good idea to make unnecessary splices.

Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!