SF375PEWN3 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Lakeside, MI
- Parts Used:
- 814269
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven /Broiler would not ignite
Determined problem was probably the igniter and ordered one. Watched internet video on igniter replacement. When igniter came read instructions and found them incomplete and ambiguous. Turned off current to stove. As per video removed oven door, racks, bottom of oven and flame deflector (only one nut holding in place.) Could then see how existing igniter was wired and understood instructions that came with igniter. Followed instructions for installation and replaced previously removed parts. Turned electricity back on and the oven/broiler gas ignited as per usual. Job took me about an hour. Could do again in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Chelmsford, MA
- Parts Used:
- WPY0060872
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner bowls were pitted, rusted, and unattractive.
After too many years of trying to make do with worn out burner bowls, I finally searched on line for Caloric replacement parts. My order arrived THE NEXT DAY(!!!)and make my old range look almost new! They are so shiny and clean, and fit perfectly. I am so pleased, and wish I had ordered from PartSelect years ago! Thank you for your speedy service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Florence, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old igniter lost power to ignite gas..
The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Weston, CO
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broiler & burners worked, oven would not ignite or heat up.
Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sapulpa, OK
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Lower Bake Ignitor would glow, but would not ignite flame.
First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VICTOR from MOUNT PROSPECT, IL
- Parts Used:
- 786324
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Screws Were Rust6Ed, Melted
Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems
Was this instruction helpful to you?
Thank you for voting!