GY395LXGB4 Whirlpool Range - Instructions

Easy.
Remove 2 screws.
Remove wires from old element.
Attach wires to new element.
Replace screws.
Took 5 minutes.

Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took the back off and put it in. It was a snap! Shouldn't have waited 1 year to do it!

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .

Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.

Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.

Replaced damaged drawer roller: easy peasy!

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564