YWFE515S0JS1 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory from BRIDGEBORO, GA
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pedro from HARLINGEN, TX
- Parts Used:
- W11047722
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
not instructions on how to install
the part conections were different from the original.so the first i did was to call parts direct to see if someone will help.NOBODY WAS ABLE TO HELP. so i had to use a lot of common sense to install this my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from PLEASANT PR, WI
- Parts Used:
- W11178521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Countertop Dishwasher - Non Whirlpool
Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amadeusz from Simi Valley, CA
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broil heater exploded. The corner was burned/ corroded.
Unplug power. Remove panel on the back. Unplug heater.From front remove 3 screws and remove heater. Installed new heater. On the back restored connections - squized the lugs to have better connection. Put panel back. Plug the power and see if the coil get red. It looked good. Used oven few times it works fine. Difficoult part is to clean oven all around from accumulated grease. First repair for this stove, most of the time spend on figuring out what to open, no instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce E from Oxford, MS
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the dial would not work unless the special screws, which are extra short, are utilized.
since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Seminole, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The large burner sometimes stayed on high too long, burning food
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Clinton, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner goes full hot at any setting
First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Cornelius, NC
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!