WFC150M0JW0 Whirlpool Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ralph from MARION, OH
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner didn’t work right
Replaced switch. Works right now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TRACY, CA
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Over heating element.
Just turn off power , remover screws. Remove and plug in new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SHELBYVILLE, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8” burner on low would run away. Burn solid red.
I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from BELLINGHAM, WA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replacing oven light and socket
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from morehead city, NC
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Greensboro, NC
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Gillett, WI
- Parts Used:
- 814399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heating coil snapped and would no longer heat.
It was so easy to change this out. Unplugged the stove and removed a couple of screws on mounting plate and pulled out the old heating element. Plugged in the new one and replaced the screws. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra Collignon from SANTA CLAUS, IN
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from OROFINO, ID
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
I decided it was the switch that was bad as it would not turn on or anything.
After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from GROVE CITY, PA
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
bunner was not shuting off automaticly
I used the replacement video from the web site. The replacement went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FOUNTAIN INN, SC
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from THE VILLAGES, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner wouldn't regulate temperature
Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TAYLORS, SC
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface element out
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from MARGATE, FL
- Parts Used:
- WPW10310922
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
It break with the time
I order the part here, the first part never arrived, it was an empty package, the second part was breaking, the glass support was missing. Broken from the vent trim, then I was tired of it so I just put back the original broken part with some super glue on it, lol
Was this instruction helpful to you?
Thank you for voting!